How To Change Kitchen Faucet ? Without Any Damaging

new kitchen faucet

Changing a kitchen faucet can be a relatively simple and straightforward DIY project that can give your kitchen a quick update. In this article, we will go over the steps involved in changing a kitchen faucet, as well as some tips and tricks to make the process as smooth as possible.

Step 1: Gather Your Tools and Supplies

Before you start the project, it’s important to gather all the tools and supplies you’ll need. These may include:

  • A new kitchen faucet
  • Adjustable wrench
  • Basin wrench
  • Plumber’s putty or silicone sealant
  • Towels or rags
  • Bucket or container to catch water

Step 2: Turn Off the Water Supply

The first step in changing a kitchen faucet is to turn off the water supply. Locate the shut-off valves under the sink and turn them clockwise to shut off the water supply to the faucet. If there are no shut-off valves under the sink, you may need to shut off the water supply to the entire house.

Step 3: Remove the Old Faucet

Next, you’ll need to remove the old faucet. Start by disconnecting the supply lines from the faucet. Use an adjustable wrench to loosen the nuts that hold the supply lines in place, and then gently pull the lines away from the faucet.

Next, use a basin wrench to loosen the nuts that hold the faucet in place. You may need to use a little force to break the seal between the faucet and the sink. Once the nuts are loosened, lift the old faucet out of the sink.

Step 4: Prepare the Sink for the New Faucet

Before you install the new faucet, you’ll need to prepare the sink. Start by cleaning the area around the holes where the faucet will be installed. Use a mild detergent and a scrub brush to remove any dirt, grime, or old sealant.

Next, apply a small amount of plumber’s putty or silicone sealant around the base of the new faucet. This will help create a watertight seal between the faucet and the sink.

Step 5: Install the New Faucet

Once the sink is prepared, it’s time to install the new faucet. Start by placing the gasket or rubber seal provided with the faucet over the mounting hole. Then, lower the faucet into the mounting hole and make sure it is centered and level.

Next, use a basin wrench to tighten the nuts that hold the faucet in place. Be careful not to overtighten the nuts, as this can damage the faucet or the sink.

Step 6: Connect the Supply Lines

With the faucet securely installed, it’s time to connect the supply lines. Start by connecting the hot and cold water supply lines to the corresponding connections on the faucet. Use an adjustable wrench to tighten the nuts, but be careful not to overtighten them.

Step 7: Turn On the Water Supply

Once the supply lines are connected, it’s time to turn on the water supply. Slowly turn the shut-off valves counterclockwise to allow water to flow to the faucet. Check for leaks around the connections and tighten the nuts if necessary.

Step 8: Test the Faucet

Finally, test the new faucet to make sure it’s working properly. Turn on the hot and cold water and check for leaks or drips. Check the water pressure and adjust the faucet handles as needed.

Tips and Tricks:

  • If you’re having trouble removing the nuts that hold the old faucet in place, try spraying them with a penetrating oil such as WD-40.
  • Before installing the new faucet, take a photo of the old faucet and the supply lines. This will make it easier to reconnect the new faucet.
  • Consider upgrading your supply lines when you install a new faucet. Braided stainless steel supply

One thought on “How To Change Kitchen Faucet ? Without Any Damaging

  1. I bought a new faucet but the service fee is too much. Is there any other way to install it ?

Leave a Reply

Your email address will not be published. Required fields are marked *